FAQ: What Is C5 Error Code On Cabrio Dryer?

Later in this list, we’ve included codes for the 2015 Cabrio dryer, too. AF – Exhaust air flow restriction. This happens when power is interrupted while the dryer is running. Press START to continue the cycle or STOP to clear the PF from the display.

How do I reset my Whirlpool Cabrio dryer?

How to Reset a Whirlpool Cabrio

  1. Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
  2. Choose a new cycle and press “Start” to begin.
  3. Turn off and disconnect the Cabrio if the error or problem persists.
  4. Wait several minutes before restoring power.

Why does my Whirlpool Cabrio dryer say af?

An AF (Restricted Air Flow) error code indicates that the lint screen or house vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.

You might be interested:  Readers ask: How Can I Get The Error Code To Display On My Bosch Dishwasher?

What is AF on Cabrio dryer?

An AF ( Restricted Air Flow ) error code indicates that the lint screen or vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present.

Where is the dryer reset button?

Often, dryers are equipped with a reset button on the control panel.

Does my Whirlpool Cabrio dryer have a reset button?

Whirlpool dryers can do many things, such as monitor moisture levels and temperature, reduce noise, periodically tumble clothes to remove wrinkles, steam clothes and adjust the overall drying time according to fabric and load size. However, one thing a Whirlpool dryer cannot do is reset itself by pushing a button.

How do you clear the fault code on a Whirlpool Cabrio?

First press PAUSE/CANCEL once to clear the Fault code from the Cabrio display. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea. (Watch The Cabrio Diagnostics Video); This will reveal any stored Fault codes.

How do you clear the AF code on a dryer?

To clear the code, press STOP once and the estimated time remaining countdown should return to the display. The AF code will continue to appear with each cycle until the low airflow condition is resolved.

Why is my Whirlpool Cabrio dryer not heating up?

No Heat. Cabrio dryers should be connected to two household fuses or circuit breakers. If one of these trips or fails, the drum will turn, but the dryer may not provide heat. Reset the breaker or replace the fuse and restart your dryer.

You might be interested:  FAQ: What Does Error Code A16 On Specturm Cable Box Mean?

What do you do when your dryer Says AF?

Try the following:

  1. Clean the lint screen.
  2. Check to see if the house vent from the dryer to the wall is crushed or kinked.
  3. Confirm that the house vent from the dryer to the wall is free of lint and debris.
  4. Confirm that the exterior vent exhaust hood is free of lint and debris.

What does it mean when dryer says AF?

The letters “AF” flashes if a restricted air flow condition exists, meaning that 3 consecutive cycles were run with airflow less that 19CFM. Check the entire venting system for any kinks or restrictions. Check the door seal and drum seals.

How do I reset my Huebsch dryer?

Step-by-Step Programming Instructions:

  1. Start with all the DIP switches in the two blocks under the display in the OFF position (down)
  2. Press reset button to clear memory.
  3. Press button to the left of the display to show start time for the dryer.
  4. Press button to the left of the display again to turn off the display.

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to Top