How To Fix Dc Error Code On Samsung Washer?

A DC code error on a Samsung washing machine indicates that the washer is unable to spin due to a load imbalance. Correcting a DC error is as simple as redistributing the weight of an existing load, removing items to reduce the overall weight in the washer, or changing suspension rods (or shock absorbers).

How do I reset the code on my Samsung washer DC?

Resetting your washing machine is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.

Why does my Samsung washer show DC?

SAMSUNG DC ERROR CODE: The DC error code shows on your washers display when your Samsung washer is unable to spin DUE to an unbalanced load. Both of the DC & UE error codes work together to tell you that you have an unbalanced load and because of that… the WASHER WILL NOT SPIN.

You might be interested:  What Does Error Code -20 Mean?

How do I fix E6 error on my washing machine?

Sometimes LG washer shows an E6 error code due to poor signal transmission. This often happens if there is a violation of the electrical circuit. To restore contact, twist and insulate the broken wires, and firmly insert the terminals into the groove.

How do you fix a DC code on a Samsung dryer?

In order error code dc to disappear completely in the Samsung dryer, you must first check the contacts with a multimeter. If the tester does not respond properly, then there is a break. Replacing the harness will help to eliminate it. It is also advisable to connect the wires by stripping and twisting or by soldering.

How do I get my Samsung washer to spin only?

To run a Spin Only cycle on a model that does not have this option on the cycle selector dial, perform the following:

  1. Power the unit on.
  2. Press and hold the spin key for approximately 3 seconds. A chime will sound.
  3. Select the spin level, if desired.
  4. Press the Start/Pause button.

What does DC1 mean on Samsung washing machine?

dE1 or dC1 The washing machine has failed to lock the door or the door does not unlock. 4E (or E2) 4C or 4C2 The water fill of the washer has failed. 5E (or E2) 5C The washing machine does not drain.

How do you rebalance a Samsung washer?

Why is it important to use calibration mode?

  1. Remove all laundry or any other contents in the machine.
  2. Power off, and then power on the washing machine on again.
  3. Hold down Temp.
  4. Press START/PAUSE to run the Calibration cycle.
  5. The drum will rotate clockwise and counterclockwise for about 3 minutes.
You might be interested:  Readers ask: What Is Error Code 1602 In Itunes?

What is E6 error in washing machine?

The E6 error is telling you that the clutch is causing the error or fault. This fault can happen if a paperclip, nail, coin, or a different object is jammed in between the tub and pulsator. To clear the E6 error code on a top load LG washer: Take out all clothing or towels from the washer.

What is E6 error?

An E6 error code is when the inside unit is unable to communicate with the outside unit. The lines have high or low voltages.

How do I reset my smart drum washing machine?

How to reset the washing machine:

  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

How do I run a diagnostic on my Samsung dryer?

Run a Vent Blockage test

  1. When you’re ready to start, make sure the drum is empty and then close the door.
  2. Press POWER to turn the dryer on and within 5 seconds, press and hold Adjust Time Up + Dry Level until InS or In appears on the display.

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to Top