- 1 How do I clear the error code 01 on my Electrolux dishwasher?
- 2 How do you clear a dishwasher error code?
- 3 How do you fix error 30 on Electrolux dishwasher?
- 4 How do I cancel my Electrolux dishwasher cycle?
- 5 Why is my Electrolux dishwasher not draining?
- 6 How do you reset your dishwasher?
- 7 What does 888 mean on a dishwasher?
- 8 How do I unlock an Electrolux dishwasher?
- 9 Why does my Electrolux dishwasher keep beeping?
- 10 Why is my dishwasher foaming?
- 11 How do I reset my Electrolux esl63010 dishwasher?
- 12 How do I drain my Electrolux dishwasher?
- 13 Why are all the lights flashing on my Electrolux dishwasher?
How do I clear the error code 01 on my Electrolux dishwasher?
’01’ error code on an Electrolux dishwasher indicated water leak. There is a sensor under Electrolux dishwashers that can detect water leaks. You should disconnect the dishwasher from its power source. Check the pumps, hoses and also the tub to look for leaks.
How do you clear a dishwasher error code?
Sometimes disconnecting power to the dishwasher for 30 seconds will clear the fault, error or function code.
How do you fix error 30 on Electrolux dishwasher?
The #30 error code indicates a leaking issue. If you don’t see a puddle, the leak could be more minor, but will still be doing damage somewhere. When this code happens, you will want to check the impeller to make sure it still turns, check the drain hose, and check the water fill valve.
How do I cancel my Electrolux dishwasher cycle?
The instructions go on to say: “To cancel when a cycle is running, open the door and press the START/CANCEL key once. Close the door again, and the dishwasher will drain and shut off ”.
Why is my Electrolux dishwasher not draining?
If the valve gets stuck closed, it will prevent the water from draining. If the check valve is stuck closed, try cleaning it out and then replace it if necessary. The drain hose might be clogged. To unclog the drain hose, remove the drain hose from both the dishwasher and the sink drain and clean it out.
How do you reset your dishwasher?
To reset a dishwasher, you need to hold the start button down for three seconds or, failing that, switch your dishwasher off at the main power supply. If that won’t sort out the glitch, you may have problems with your power, water source, door latch, or internal issues.
What does 888 mean on a dishwasher?
888 means the PC board is shorted and the display driver that shows what supposed to be a display is not working,I would take the PC board out of the machine,look for water corrosion,it will be like a white puffy kind of stuff,if you see that,you have water damage from some other part inside.
How do I unlock an Electrolux dishwasher?
If your Electrolux dishwasher door locked and won’t open, this code will appear. You won’t be able to run a cycle without unlocking the door. Press and hold the AIR DRY button on the control panel for at least 3 seconds while the door is latched. This should unlock the door or activate the control panel for use again.
Why does my Electrolux dishwasher keep beeping?
If the dishwasher beeps 3 times or the LED flashes 3 times it indicates a leak, and water collecting at the bottom of the appliance. To resolve the issue, contact an Authorized Service Center. Warning: Turn off the dishwasher water supply to avoid flooding.
Why is my dishwasher foaming?
This is caused by one thing – using the wrong product in the dishwasher. Dish soap that you use to wash dishes in the sink is not the same soap used in a dishwasher. If you do put it in there, either as residue on dishes or just as the detergent, it will foam up like crazy.
How do I reset my Electrolux esl63010 dishwasher?
To reset press and hold S2 and S3 buttons for approximately 5 seconds. S0 is ON/OFF button then S1 is first button towards right of it and so on.
How do I drain my Electrolux dishwasher?
When the Electrolux begins draining, open the cabinet door under the kitchen sink. Find the transparent drainage hose that runs from the the dishwasher and connects to the garbage disposal chamber underneath the sink drain. Look for used water to drain through the hose.
Why are all the lights flashing on my Electrolux dishwasher?
If the water doesn’t reach the proper temperature after a set amount of time, a light on the control panel might start flashing. To determine if the heating element has burned out, use a multimeter to test it for continuity. If the heating element does not have continuity, replace it.