Question: How To Fix Samsung Washing Machine Error Code 1e?

Samsung washing machine IE error – Possible solutions

  1. Do a hard power reset. You need to unplug your Samsung washing machine for about 5 minutes as this will normally reset most of the electronic glitches or any other issues with software that may be present.
  2. Ensure proper wire connection.
  3. Replace the pressure switch.

How do I fix error code 1E?

Disconnect the strainer, clean and rinse it, as it may become clogged. Check the condition of the hose. It is possible that it is pinched, clogged, bent or twisted. Unplug the washing machine: unplug the cord and plug it into the power outlet after 5-10 minutes to reset error code 1E.

What is the meaning of 1E in Samsung washing machine?

Samsung malfunction 1E or 1C This means that the water pressure or water level is not correct. First check whether the washing machine is properly connected to the water supply. The supply hose may be clogged or kinked.

You might be interested:  Readers ask: What Is Error Code 272 In Roblox?

How do I fix E1 error on my washing machine?

Question: Error Code-control panel display “E1” Drain error, water can not drain fully within the required drain time (controlled by PCB software ). Solution: Remove and clean the pump filter. Check drain hose for blockage and proper installation.

Why does my washer keep saying IE?

An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen. Once the temperature increases above freezing, the water supply will resume.

What is E1 error in washing machine?

When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water. To resolve, checking the following: • Check whether the water supply is turned on and that there is adequate water pressure.

How do I reset my Samsung washing machine?

Reset your washing machine Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.

What is UB error in Samsung washing machine?

When you see a “UB” washer error code, that means the washer drum is unbalanced. Typically, the drum will stop, halting the spin cycle – and will not restart until the unbalanced load condition is fixed.

You might be interested:  FAQ: 80246007 Error Code When Update Runs?

How do I clear the E1 error on my Whirlpool washer?

Check the following:

  1. Check that the water faucets are not closed.
  2. Check that the water pressure in the house is over 20 kPa.
  3. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
  4. Check that the drain hose is not below 27½” (700 mm) from the floor.

What E1 means?

E1 means ” Everyone.”

Why is my washing machine not draining?

Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.

How do I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do I fix the error code on my LG washer?

How to reset the washing machine:

  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

Why is my LG washer not draining?

Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to Top