Quick Answer: How Do I Clear An Error Code On A Fisher Paykel Dishwasher?

To attempt to Clear the Fault Code

  1. Press to stop the beeping. Press. again to turn the dishwasher off.
  2. Wait a few seconds. Press. again to turn the dishwasher back on.

How do I reset my Fisher and Paykel dishwasher?

Reset Procedures for the Fisher & Paykel Dishwasher

  1. Press the power button to turn off power to the Fisher & Paykel dishwasher.
  2. Wait a few minutes and then press the power button to restore power.
  3. Turn off and unplug the dishwasher if the issue remains.
  4. Wait five minutes and restore power to the unit.

How do I cancel my wash cycle on my Fisher Paykel dishwasher?

To cancel, press and hold until the light above it goes out. Press to cancel a wash that has already started or to cancel the Delay start setting. If there is any water in the drawer,it will automatically drain before the dishwasher turns off.

You might be interested:  Often asked: What Is Error Code 486?

How do I fix E6 error on Fisher and Paykel dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.

How do you run a diagnostic on a Fisher Paykel dishwasher?

Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.

Why is my Fisher and Paykel dishwasher not draining?

Straighten any kinks along the hose that drains water from your DishDrawer™. If the kinks return, you may need to replace the hose. Clean the filter plate/drain filter. Aim to clean your DishDrawer™ at least once per month, including the drain filter plates.

What does F1 mean on a Westinghouse dishwasher?

An F1 error code on your Westinghouse dishwasher indicates that a leak is detected somewhere in the unit, whereas an F3 error code pinpoints the issue to a problem with the overflow protector. The overflow protector is normally located in the front left corner of the dishwasher tub.

What does F1 error mean?

F1 Error. The F1 error means that there is an electronics failure within the oven. This failure can occur within the keypad itself, the electronic oven control or the oven temperature sensor. The error can also indicate data corruption within the oven’s electronic controller.

Why is my dishdrawer beeping?

The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. once to stop the beeping, and then again to clear the fault. to resume the wash program.

You might be interested:  Quick Answer: What Is A Permissions Error Code Web?

How do I start my Fisher and Paykel dishwasher?

Operating Instructions – Starting a Wash

  1. Discard scraps.
  2. Load dishes carefully.
  3. Check spray arm(s) are mounted correctly and can rotate fully around.
  4. Add detergent / Check rinse aid.
  5. Select wash.
  6. Start wash or set Delay start.

How long is Fisher Paykel dishwasher cycle?

Normal Eco (~158 Mins) Wash times can vary depending on the incoming water temperature, ambient conditions, type of dish load and whether the drawer has been opened during the wash.

What does E6 mean on a dishwasher?

An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.

How do I fix e5 error on my dishwasher?

Switch the power off and restart the dishwasher To do this you need to press the on/off button on the machine. When you have clicked the button wait a few minutes. Restart the dishwasher using the same button.

What does F24 mean on my Fisher and Paykel dishwasher?

F24. Motor Fault – Stalled, Stopped or Overloaded. Check for Obstructions jamming Motor Rotor – Refer to User Guide on how to remove the Rotor.

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to Top