Quick Answer: What Is The Error Code For A Whirpool Duet Drain Pump?

The Whirlpool washer error code F21 means the washing machine has a “water draining issue”, meaning the drain pump itself, or the drain hose is clogged and the washer is having problems draining the water out.

How do I know if my whirlpool drain pump is bad?

Check the pump pulley by removing the pump from the washer and trying to rotate it by hand. If the pulley doesn’t turn freely and is frozen or stiff, replace it. Also, if the agitator is moving but the tub isn’t, this is a sign the pump is dying.

How do I clear the error on my Whirlpool Duet washer?

Press the “Pause/Cancel” button on the control panel twice to clear the error. Contact a certified repair technician if pressing the “Pause/Cancel” button does not clear the error, as this indicates that a component has failed in the washing machine or dryer.

Why does my washer say F 21?

If you see error code F21 on your Whirlpool washing machine, this refers to a water drain problem. The washer won’t be able to finish the cycle and your laundry will be wet. This error code means draining is taking too long, and something is wrong with the water pumping.

You might be interested:  Often asked: What Does Error Code 10 Mean Iphone?

How do you know if your washing machine drain pump is broken?

Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you’ll be able to feel them while you’re turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.

Do Whirlpool washers have a reset button?

Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

How do you reset a Whirlpool Duet front load washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

Why does my washer keep saying F?

The F indicates that the washer control detected a component problem. Since the door remained locked, your likely problem was with the drain pump or excessive suds preventing the washer from draining out the water properly.

How do you fix a Whirlpool washer that won’t drain?

What to Do When Your Washing Machine Won’t Drain

  1. Perform a Master Reset. Unplug your washer for about one minute.
  2. Test the Lid Switch Assembly.
  3. See if the Drain Hose is Kinked.
  4. Check the Drain Hose or Pump for Clogs.
  5. Clean out the Coin Trap.
  6. Check the Water Level Control.
  7. Schedule Washing Machine Repair.
You might be interested:  Readers ask: How To Fix Ny Netflix Error Code Ui-800-3?

What does LO FL mean on my Whirlpool washer?

The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive.

Why does my Whirlpool washer not start?

One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.

How do you unlock a Whirlpool front load washer?

Press the “Drain and Spin” button on the washer’s control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to Top