Readers ask: Lg Dishwasher Error Code Oe How To Fix?

OE Error Code – Dishwasher

  1. Check for food debris. If you notice any food debris in the tub of your dishwasher, remove larger food debris and items that may not wash out.
  2. Clean the filter.
  3. Check the drain hose.
  4. Check the air gap.
  5. New dishwasher or gabage disposal.
  6. Force the Drain.
  7. Request a Repair.
  8. Important Tip.

How do I reset the OE code on my LG dishwasher?

First, inspect the drain hose for a clog or bend. Second, inspect the dishwasher drain pump for any blockages in the pump housing assembly. Clean any and all blockages and the OE error code should clear.

How do I unclog my LG dishwasher drain?

Follow these steps to unclog an LG dishwasher drain hose:

  1. Unplug the dishwasher.
  2. Remove the lower front panel.
  3. Disconnect the hose from the drain pump.
  4. If a clog is visible at either end of the hose, carefully remove it with a straightened wire hanger.

How do you clear a dishwasher error code?

Sometimes disconnecting power to the dishwasher for 30 seconds will clear the fault, error or function code.

You might be interested:  What Is Error Code -50?

Why is my LG dishwasher not draining?

If the valve gets stuck closed, it will prevent the water from draining. If the check valve is stuck closed, try cleaning it out and then replace it if necessary. The drain hose might be clogged. To unclog the drain hose, remove the drain hose from both the dishwasher and the sink drain and clean it out.

How do I test my LG dishwasher drain pump?

Test the drain pump.

  1. Press POWER to turn the washer ON.
  2. Press the SPIN SPEED key until HIGH is selected.
  3. Press the START/PAUSE button to start the SPIN ONLY cycle.
  4. Listen to hear a humming sound which indicates that the drain pump motor has started working.

How do I know if my dishwasher drain pump is bad?

If your dishwasher has a timer, turn the timer dial to the drain portion of the cycle to run the drain pump. Listen for the drain pump running. If the drain pump runs but doesn’t pump water and the drain path is clear, then the drain pump is likely bad.

Why is my LG front load washer not draining?

Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.

Where is the drain pump on LG dishwasher?

With the bottom of your dishwasher exposed, use a screwdriver to remove the large access panel covering the drain pump. Once the panel is detached, locate the drain pump, and disconnect the wire harnesses running to it.

You might be interested:  FAQ: What Is 500 Error Code In Http?

How do I reset my LG dishwasher?

This can usually be corrected by performing the following steps:

  1. Press the POWER button to turn the dishwasher off.
  2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds.
  3. Turn the circuit breaker to the dishwasher back ON.
  4. Press the POWER button to turn the dishwasher ON, and start a new cycle.

How do you reset your dishwasher?

To reset a dishwasher, you need to hold the start button down for three seconds or, failing that, switch your dishwasher off at the main power supply. If that won’t sort out the glitch, you may have problems with your power, water source, door latch, or internal issues.

How do I reset my leaky GE dishwasher?

You can reset a GE dishwasher by pressing the Start or Reset button. If you have a top-loading dishwasher, you need to open the top, press the button, and close it. Wait 2 minutes for the dishwasher to drain the water. Add any additional dishes after 2 minutes.

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to Top